---
title: 事件推送
editLink: false
---
# 事件推送

事件推送功能，由设备端EMS触发，向客户APP进行消息推送的功能。主要用于在某些事件节点上给用户一个提示，以便知晓设备的功能执行情况及一些处理措施。

事件推送表（中文）:

| ID | 标题 | 内容 |
| :-: | :-: | ---- |
| 1 | 市电停电 | 电网中断了。FHP已经存储了$1kWh，根据过去72小时的最高消耗，大约可以提供$2的备电时长。 |
| 2 | 市电恢复 | 已恢复至并网工作。 |
| 3 | 电量低 | FHP电量低 。 |
| 4 | 电量极低 | FHP电量极低，该设备即将进入休眠状态。 |
| 5 | 黑启动失败 | FHP系统黑启动失败。 |
| 6 | EPO停机 | 由于EPO动作，家庭供电被切断。 |
| 7 | EPO复位 | EPO复位，家庭供电恢复。 |
| 8 | 发电机接入 | 发电机正常运行，并已接入FHP系统。 |
| 9 | 发电机退出 | 发电机退出FHP系统。 |
| 10 | 紧急备电开始 | aGate已收到风暴通知，正在以紧急备用模式为电池充电。 |
| 11 | 紧急备电结束 | 风暴信息变更，aGate将退出风暴模式，恢复先前的工作模式。 |
| 12 | 固件升级开始 | FHP系统开始升级。 |
| 13 | 固件升级结束 | FHP系统升级完成。 |
| 14 | 系统停止 | FHP进行系统保护。 |
| 15 | aPower停止 | aPower设备发生故障。 |
| 16 | 离网过载 | 由于过载导致系统暂时保护。 |
| 17 | 智能负载断开 | FHP系统电量低于限值，已断开智能负载。 |
| 18 | 智能负载断开 | FHP系统电量低于限值，已断开智能负载。 |
| 19 | 智能负载低SOC切断恢复 | |
| 20 | 离网超发断光伏 | |
| 21 | 离网恢复光伏 | |
| 22 | 启动发电机 | |
| 23 | 停止发电机 | |
| 24 | 发电机启动异常 | 由于\{0\}，导致发电机启动异常 |
| 25 | 发电机运行异常 | 发电机运行异常，发电机将被关闭。 |
| 26 | 系统休眠 | FHP系统电量耗尽，进入长时休眠状态。 |
| 27 | 离网过载预警 | 负载功率超过FHP系统额定功率，即将触发系统保护。 |
| 28 | 光伏接入尝试 | 发电机输出不稳定，无法对电池充电。系统正在尝试接入光伏充电。 |
| 29 | 黑启动尝试 | 系统正在进行黑启动尝试。 |
| 30 | 离网过载锁定 | 频繁触发系统过载保护，系统锁定。 |
| 31 | 系统电量恢复 | 系统电量已经恢复至20%。 |
| 32 | 智能线路已充满 | 智能线路已充满，退出定量充电。 |
| 33 | 发电机演习成功 | 发电机演习成功 |
| 34 | 发电机演习失败 | 发电机演习失败，可能是由于启动超时或其他异常情况 |
| 35 | 发电机工作不稳定 | 发电机工作不稳定，aPower可能会进入待机模式 |
| 36 | 发电机恢复稳定 | 发电机恢复稳定工作状态 |
| 37 | 进入休眠模式 | 电池设备因线路异常进入休眠状态，请恢复线路后再试 |
| 38 | V2L接入 | 系统已经接入V2L紧急电源模式，现在已经可以使用您的电动汽车为系统提供供载。请您注意降低家庭负载消耗功率。 |
| 39 | V2L退出 | 电动汽车供载结束，系统已经退出V2L紧急电源模式。 |
| 40 | 紧急备电模式退出 | 备电结束，aGate已切换至\{0\}模式。 |
| 41 | V2L输出过载保护告警 | 您正在使用V2L模式。目前您的电动汽车输出功率已达到额定功率的 80%，请注意负载消耗情况。 |
| 42 | V2L输出过载切断 | 您正在使用V2L模式。您的电动汽车输出功率已超过额定功率，V2L线路已切断。 |
| 43 | PCS保护限制光伏 | 主电池板工作电流超过设定值的95%，需要限制光伏。 |
| 44 | PCS保护切断智能负载 | 主电池板工作电流超过设定值的 100%，$1已被切断。 |
| 45 | V2L启动异常 | 由于\{0\}，导致V2L启动异常 |
| 46 | - | - |
| 47 | - | - |
| 48 | PCS保护调节电池功率 | 主电池板工作电流超过设定值的 90%，需要调节电池功率。 |
| 49 | 退出PCS保护调节电池 | 主面板工作电流降低到设定值的 85%，退出电池功率调节。 |
| 50 | 退出PCS保护，恢复光伏 | 主面板工作电流降低到设定值的 85%，恢复光伏。 |
| 51 | 退出PCS保护，恢复智能负载 | 由于主面板工作电流降至设定值的 80%，$1已恢复。 |
| 1401 | 系统暂停 | FHP暂时保护，请等待系统尝试恢复。 |
| 1402 | 系统停止 | FHP进行系统保护。 |
| 1403 | 系统异常 | 系统检测异常。 |

事件推送表（英文）:

| ID | Title | Content |
| :-: | :-: | ---- |
| 1 | Grid Outage | There is a grid outage. aGate has stored $1kWh for an estimated $2 of backup based on the highest consumption in the past 72h. |
| 2 | Grid restored | Grid power has been restored. |
| 3 | Low SOC | aGate battery storage is at SOC lower limit. |
| 4 | Extremely low SOC | The aGate will enter sleep mode as the stored energy is almost depleted. |
| 5 | Black start failure | The aGate failed to black start. |
| 6 | EPO downtime | The home is powered off due to EPO activation. |
| 7 | EPO replaced | The EPO has been reset your home is powered. |
| 8 | Generator access | The generator is connected and supplying the home. |
| 9 | Generator exit | Generator has been turned off. |
| 10 | Emergency backup start | The aGate has received a storm notification and is charging the battery in emergency backup mode. |
| 11 | Emergency backup end | Storm information has changed. The aGate will be out of storm mode, and resume the previous operating mode. |
| 12 | Firmware upgrade | Your aGate is upgrading. |
| 13 | Firmware upgrade completed | Your aGate upgrade is completed. |
| 14 | aGate shutdown | Your aGate shut down for self-protection. |
| 15 | aPower failure | There is an aPower malfunction. |
| 16 | System overloading | Your aGate temporarily shut down due to an overload. |
| 17 | Smart Circuits disconnected | The Smart Circuits have been disconnected as the battery SOC battery is below the set threshold. |
| 18 | Smart Circuits disconnected | The Smart Circuits have been disconnected as the battery SOC battery is below the set threshold. |
| 19 | Smart circuit reconnected | |
| 20 | Solar disconnected | |
| 21 | Solar reconnected | |
| 22 | Generator start | |
| 23 | Generator stop | |
| 24 | Generator start abnormality | Generator start abnormality due to \{0\}. |
| 25 | Generator abnormality | Your aGate is powered off due to battery depletion. |
| 26 | System power-off | Your aGate is powered off due to battery depletion. |
| 27 | Off-grid overload warning | Your aGate over-protection is about to be triggered, as your loads are overloading the battery. |
| 28 | Solar attempt | The generator output is unstable and cannot recharge the battery. The aGate is attempting to charge the battery from solar. |
| 29 | Black startup attempt | Your aGate is attempting a black start. |
| 30 | aGate shutdown due to overload | The aGate shut down due to frequent overload protection. |
| 31 | Battery power recovery | FHP battery has been recharged to SOC 20%. |
| 32 | The load on the smart circuit is fully charged | The load on the smart circuit is full, the quantitative charging will end. |
| 33 | Generator exercise success | Generator exercise success. |
| 34 | Generator exercise fail | Generator exercise fail, possibly due to startup timeout or other abnormal conditions. |
| 35 | Generator instability | The generator is unstable and the aPower(s) may enter standby mode. |
| 36 | Generator stabilization | The generator returned to stable operation. |
| 37 | Enter hibernation mode | The battery device went into hibernation mode due to a circuit abnormality. Please restore the circuit and try again. |
| 38 | V2L mode access | V2L emergency power mode is enabled, and your EV is ready to power home loads. You might need to reduce in-essential home loads. |
| 39 | V2L mode exit | Your EV has stopped powering loads, V2L emergency power mode is turned off. |
| 40 | Emergency backup over. The aGate has been switched to the XXX(Previous mode) mode. | Emergency backup over. The aGate has been switched to the XXX(Previous mode) mode. |
| 41 | V2L output overload protection alarm | You are using V2L mode. Currently the output power of your electric vehicle has reached 80% of the rated power, please pay attention to the load consumption. |
| 42 | V2L output overload cut off | You are using V2L mode. The output of your electric vehicle exceeds the rated power. The V2L line has been disconnected. |
| 43 | PCS protection to limit solar | Main panel operating current exceeds 95% of the set value, requires limiting the solar. |
| 44 | PCS protection to shed smart circuits | Your house is using too much power and is nearing the safe limit of operation. $1 of your Smart Circuit is being temporarily disconnected until the home load decreases. |
| 45 | V2L start abnormality | V2L start abnormality due to \{0\}. |
| 46 | - | - |
| 47 | - | - |
| 48 | PCS protection to regulate battery power | Your house is using too much power and is nearing the safe limit of operation. Regulating the battery power until the home load decreases. |
| 49 | Exit PCS protection to regulate battery power | Main panel operating current is reduced to 85% of the set value, exiting battery power regulation. |
| 50 | Exit PCS protection, restore solar | Main panel operating current is reduced to 85% of the set value, restore solar. |
| 51 | Exit PCS protection, restore smart circuits | Power to the $1 of Smart Circuit has been restored. Your home load has reduced to safe limits. |
| 1401 | aGate suspension | Your aGate temporarily stopped working, and it will restart automatically. |
| 1402 | aGate shutdown | The aGate detected an abnormality. |
| 1403 | aGate abnormality | The aGate detected an abnormality. |

## No.1 市电停电(Grid Outage)

FWH系统从并网运行模式切换到离网运行模式，市电停电或市电质量不满足可正常使用标准。

## No.2 市电恢复(Grid restored)

市电恢复正常，FWH系统由离网运行模式切换到并网运行模式，系统接入市电。

## No.3 电量低(Low SOC)

FWH系统电量低于10%，提醒用户注意电量使用情况。

## No.4 电量极低(Extremely low SOC)

FWH系统电量为0%，系统即将关机。

等待市电来电或黑启动尝试（每天10:00/12:00/14:00）

:::warn
aPower预留了5%的SOC用于黑启动尝试，黑启动尝试时电量可能会被负载消耗掉，导致黑启动尝试失败或者尝试次数锐减。请断开家中所有负载，以便提高黑启动成功率，避免电池完全耗尽。

当电池完全耗尽时，将无法进行黑启动尝试，只能使用市电或油机给系统补电。

当电池完全耗尽后，电芯一般只能维持大概15天左右，维护人员需在这个期限内及时补电，否则将会给电池带来不可逆的损伤。
:::

## No.5 黑启动失败(Black start failure)

代码中已经屏蔽此事件，不会推送。

## No.6 EPO停机(EPO downtime)

EPO按钮被按下，系统进入紧急停机状态。

## No.7 EPO复位(EPO replaced)

EPO按钮复位，系统将重新初始化并尝试开机。

## No.8 发电机接入(Generator access)

发电机已经正常接入FWH系统，供载或充电。

## No.9 发电机退出(Generator exit)

发电机断开与FWH系统的连接。
- 演习完成退出
- 油机启动超时退出（油机未正常启动或油机启动超时时间设置过短）
- 油机故障退出（[发电机快检异常](./AlarmTable.md#301a-发电机快检异常)、[发电机锁相失败](./AlarmTable.md#301b-发电机锁相失败)、[发电机输出不稳](./AlarmTable.md#301c-发电机输出不稳)、[发电机故障退出](./AlarmTable.md#3020-发电机故障退出)）

## No.10 紧急备电开始(Emergency backup start)

进入紧急备电状态，系统将开始使用电网充电，并将电池充至100%，为极端天气情况提供电力支持。

## No.11 紧急备电结束(Emergency backup end)

极端天气已结束，紧急备电状态解除，系统恢复到正常运行模式。

## No.12 固件升级开始(Firmware upgrade)

接收到云端固件升级请求，开始升级设备固件。

## No.13 固件升级结束(Firmware upgrade completed)

固件升级流程结束，升级结果可在Fleetview中查看。

## No.14 系统停止(aGate shutdown)

系统停止运行，有以下几种可能性：
- EPO被按下
- NewHome站点
- 所有aPower开关被置于off状态或处于故障状态无法开机
- 系统升级中

## No.15 aPower停止(aPower failure)

有一台或多台aPower处于非正常运行状态，可能原因：
- 有一台或多台aPower开关被置于off状态
- 有一台或多台aPower进入故障状态导致关机
- 系统升级，关闭aPower
- 油机运行不稳定，关闭aPower

## No.16 离网过载(System overloading)

离网运行模式下，系统长时间超出额定功率放电供载，说明此时系统负荷过大，需降低家庭负载。

此时可能会伴随着以下故障：
- [BMS-SOP限功率保护](./AlarmTable.md#4x68-bms-sop限功率保护)
- [逆变过载保护](./AlarmTable.md#4x07-逆变过载保护)

## No.17 智能负载断开(Smart Circuits disconnected)

当开启智能负载的SOC阈值(SOC Threshold)功能时，离网系统的SOC低于此阈值后会断开智能负载并推送此消息。

## No.18 智能负载断开(Smart Circuits disconnected)

此消息未使用，与No.17重复。

## No.19 智能负载低SOC切断恢复(Smart circuit reconnected)

此消息未使用。

## No.20 离网超发断光伏(Solar disconnected)

触发[光伏继电器异常断开](./AlarmTable.md#3023-光伏继电器异常断开)故障后，推送此消息。

此消息通常还会伴随着以下故障同时出现：
- xxxxx
- xxxxx

## No.21 离网恢复光伏(Solar reconnected)

[光伏继电器异常断开](./AlarmTable.md#3023-光伏继电器异常断开)故障消息后，推送此消息。

## No.22 启动发电机(Generator start)

满足发电机启动条件，尝试启动并接入发电机。

发电机启动条件如下：
- 发电机演习
- 到达用户设定的发电机充电启动时间
- 系统SOC低于用户设定的发电机启动SOC
- 用户使用APP操作手动启动发电机

## No.23 停止发电机(Generator stop)

满足发电机停止条件，尝试停止发电机并端口发电机继电器。

发电机停止条件如下：
- 发电机启动超时，在设定的发电机启动时间内，发电机无法启动或保持稳定运行(同时会伴随No.24事件)
- 演习完成退出
- 到达用户设定的发电机充电结束时间
- 系统SOC高于用户设定的发电机停止SOC
- 用户使用APP操作手动停止发电机
- 光伏尝试(同时会推送No.28事件)

## No.24 发电机启动异常(Generator start abnormality)

发电机启动超时，触发此事件。

## No.25 发电机运行异常(Generator abnormality)

[发电机故障退出](./AlarmTable.md#3020-发电机故障退出)告警出现时，会触发此推送。

## No.26 系统休眠(System power-off)

进入系统休眠时，推送此事件。

休眠共有以下几种情况：
- NewHome休眠，休眠设定时间30天
- 黑启动失败休眠，休眠至下次黑启动时间
- 所有aPower SOC下降至0.5%，深度休眠，休眠设定时间30天

## No.27 离网过载预警(Off-grid overload warning)

当有某台或多台aPower报出[输出过载告警](./AlarmTable.md#4x14-输出过载告警)时，触发此推送。

## No.28 光伏接入尝试(Solar attempt)

发电机运行过程中，如果处于中午可能太阳较大的时间点（10点、12点、14点），发电机会尝试退出，并接入光伏，尝试使用光伏充电，此时会推送此事件。

## No.29 黑启动尝试(Black startup attempt)

在系统SOC低于0%而导致的休眠后，当到达黑启动尝试时间点（10点、12点、14点）时，系统将开机，接入光伏，尝试黑启动。此时将会推送此事件。

:::warn
此时应提示用户减载，避免因负载导致快速耗尽电池电量，导致系统长期休眠，无法充电。

电池耗尽后，需及时补电，否则可能对电池照成不可逆的伤害。
:::

## No.30 离网过载锁定(aGate shutdown due to overload)

系统连续输出过载导致触发告警：[输出过载20次锁定](./AlarmTable.md#4x1c-输出过载20次锁定)

提示用户家中负载过重或电器出现短路现象。

## No.31 系统电量恢复(Battery power recovery)

系统电量恢复消息，提示用户系统已退出低电量状态（系统SOC高于20%）。

## No.32 智能线路已充满(The load on the smart circuit is fully charged)

暂未实现。。。

## No.33 发电机演习成功(Generator exercise success)

油机演习完成消息推送。

## No.34 发电机演习失败(Generator exercise fail)

油机演习失败消息推送。常伴随着油机故障出现。

以下情况会出现油机演习失败：
- 演习中触发EPO按钮

## No.35 发电机工作不稳定(Generator instability)

## No.36 发电机恢复稳定(Generator stabilization)

## No.37 进入休眠模式(Enter hibernation mode)

## No.38 V2L接入(V2L mode access)

## No.39 V2L退出(V2L mode exit)

## No.40 紧急备电模式退出(Emergency backup over. The aGate has been switched to the XXX(Previous mode) mode.)

## No.41 V2L输出过载保护告警(V2L output overload protection alarm)

## No.42 V2L输出过载切断(V2L output overload cut off)

## No.43 PCS保护限制光伏(PCS protection to limit solar)

## No.44 PCS保护切断智能负载(PCS protection to shed smart circuits)

## No.45 V2L启动异常(V2L start abnormality)

## No.46 *预留

## No.47 *预留

## No.48 PCS保护调节电池功率(PCS protection to regulate battery power)

## No.49 退出PCS保护调节电池(Exit PCS protection to regulate battery power)

## No.50 退出PCS保护，恢复光伏(Exit PCS protection, restore solar)

## No.51 退出PCS保护，恢复智能负载(Exit PCS protection, restore smart circuits)

## No.1401 系统暂停(aGate suspension)

## No.1402 系统停止(aGate shutdown)

## No.1403 系统异常(aGate abnormality)